The light level at which the output becomes saturated is about 10 mW, although depending on the element size, incident light spot size, and reverse bias. To avoid possible damage to the photodiode, use it at a light level of 1 W/mm2 or less.
Photodiode noise is expressed by the square root of the sum of the squares of the Johnson noise and the squares of the shotnoise. Johnson noise is dependent on dark current. Dark current is temperature-dependent, so the dark current decreases with a drop in the sensor temperature. Shot noise, however, has no temperature dependence except for special cases (near cutoff wavelength). As the temperature drops, the photodiode noise also tends to decrease. Contact our sales office for formulas for calculating noise.
Photovoltaic detectors generate a current when exposed to light. Photoconductive detectors change their electrical resistance (conductivity) when exposed to light and a bias voltage or current must be applied for use.
Chopping is not always required. However, chopping is commonly used to improve the S/N by distinguishing signal light from extraneous light in the surrounding environment, etc.
A general guide to chopping frequencies is shown below. The lower chopping frequency depends on the 1/f noise of the detector itself, while the higher chopping frequency is limited by the response speed of the detector. So we recommend using a chopping frequency in the flat region unless a specific problem arises. The chopping frequency we use for testing InSb photoconductive detectors is 1200 Hz.
|Product name||Chopping frequency|
|InSb photoconductive detector||Several kHz|
The signal value is not dependent on the photosensitive area, but the noise is inversely proportional to the square root of the photosensitive area. The S/N is proportional to the square root of the photosensitive area.
To re-evacuate a metal dewar, use the dedicated re-evacuation tool (A3515 valve operator for metal dewar) by connecting it to an exhaust device. We also perform re-evacuation for customers (a service fee is charged).
After the white vapor that is generated when liquid nitrogen is injected can no longer be seen, wait for 10 minutes to elapse before using.
The nitrogen cooling hold time of a typical metal dewar is approximately 20 hours immediately after purchase. The hold time gradually decreases, and after one year it is about 10 hours. So re-evacuation is needed once every few years.
The higher the object temperature, the higher the emission energy, so the wavelength distribution shifts to the short wavelength side. At low temperatures, on the other hand, the energy is small, so the wavelength distribution shifts to the long wavelength side and the energy level at short wavelengths suddenly drops. A general guide to detectors suited for different object temperatures is shown below.
|Temperature of object||Detector|
|500 ℃ or higher||Si|
|200 ℃ or higher||InGaAs|
|100 ℃ or higher||InAs|
|50 ℃ or higher||InSb, InAsSb (8 μm band)|
|0 ℃ or higher||InAsSb (10 μm band)|
|-50 ℃ or higher||Thermopile, Type-II superlattice infrared detector|
It looks like you're in the . If this is not your location, please select the correct region or country below.
You're headed to Hamamatsu Photonics website for GB (English). If you want to view an other country's site, the optimized information will be provided by selecting options below.
For modern websites to work according to visitor’s expectations, they need to collect certain basic information about visitors. To do this, a site will create small text files which are placed on visitor’s devices (computer or mobile) - these files are known as cookies when you access a website. Cookies are used in order to make websites function and work efficiently. Cookies are uniquely assigned to each visitor and can only be read by a web server in the domain that issued the cookie to the visitor. Cookies cannot be used to run programs or deliver viruses to a visitor’s device.
Cookies do various jobs which make the visitor’s experience of the internet much smoother and more interactive. For instance, cookies are used to remember the visitor’s preferences on sites they visit often, to remember language preference and to help navigate between pages more efficiently. Much, though not all, of the data collected is anonymous, though some of it is designed to detect browsing patterns and approximate geographical location to improve the visitor experience.
Certain type of cookies may require the data subject’s consent before storing them on the computer.
This website uses two types of cookies:
There are two ways to manage cookie preferences.
If you wish to restrict or block web browser cookies which are set on your device then you can do this through your browser settings; the Help function within your browser should tell you how. Alternatively, you may wish to visit www.aboutcookies.org, which contains comprehensive information on how to do this on a wide variety of desktop browsers.
Occasionally, we may use internet tags (also known as action tags, single-pixel GIFs, clear GIFs, invisible GIFs and 1-by-1 GIFs) at this site and may deploy these tags/cookies through a third-party advertising partner or a web analytical service partner which may be located and store the respective information (including your IP-address) in a foreign country. These tags/cookies are placed on both online advertisements that bring users to this site and on different pages of this site. We use this technology to measure the visitors' responses to our sites and the effectiveness of our advertising campaigns (including how many times a page is opened and which information is consulted) as well as to evaluate your use of this website. The third-party partner or the web analytical service partner may be able to collect data about visitors to our and other sites because of these internet tags/cookies, may compose reports regarding the website’s activity for us and may provide further services which are related to the use of the website and the internet. They may provide such information to other parties if there is a legal requirement that they do so, or if they hire the other parties to process information on their behalf.
If you would like more information about web tags and cookies associated with on-line advertising or to opt-out of third-party collection of this information, please visit the Network Advertising Initiative website http://www.networkadvertising.org.
We use third-party cookies (such as Google Analytics) to track visitors on our website, to get reports about how visitors use the website and to inform, optimize and serve ads based on someone's past visits to our website.
You may opt-out of Google Analytics cookies by the websites provided by Google:
We inform you that in such case you will not be able to wholly use all functions of our website.